• The measurement from outside to outside of the front bumper cover may not exceed 81.5 inches
• The measurement from the front wheel tire bead surface located at axel height at it's rearward most point and the outside surface of nose piece/front bumper cover cannot exceed 4.0 inches
• No part of the body may extend past an imaginary that originates 2 inches out from the front wheel tire bead bead and extends rearward through a point 2 inches out from the rear wheel tire bead
• All 4 wheels must be covered by body panels
  
               
  ________________________________________________________________________________
  
   
   

• Numbers are the sole property of the New England Truck Series.
• A  minimum 24-inch high, 3-inch stroke must be located on the door area on both sides of the race truck.
•  A minimum of 30-inch high, 3-inch stroke number is required on top of roof facing the passenger side of the truck.
• One or two digit numbers only unless pre-approved
• Duplicate numbers not allowed
• Trucks with existing numbers shall be offered a renewal period in which to register for 2023.
• The truck is not considered registered until the registration fees are paid in full.
• Approval of the application , and assignment of numbers is at the sole discretion of WTC Series officials.

• No bars allowed outside of bodywork
  • includes nerf bars, tow bars, push bars and bumpers
    and external bars made of  unconventional materials such as polycarbonate and carbon fiber
  • Rule may be waived for 1 event at the discretion of officials
• RUB RAILS: If used, must be carbonate type as manufactured by Five star bodies or similar.
                          No solid types; must be mounted directly to body. Only (1) per side.

• Must remain sealed at fenders
• No cutting or holes allowed

• 55 inches
• New Five Star design 56 inches
  
• Measured 10 inches back from leading edge of  roof

• Minimum Rear deck height 38 inches
• Max rear deck height 40 inches
• Must seal with the exception of openings for Automatic Transmission cooler ventilation.

• Flat-no lips or bends
• 10 inch
• Must extend entire width of rear deck
• May be braced from behind only
  • Spoiler must maintain setting with 15 lbs of pressure applied.
• Minimum 55 degrees
  • May be changed at discretion of series
  • Trucks that have spoilers that do not meet all of the above conditions at inspection
    will be assessed a 50 lb weight penalty. Spoiler must pass before competing.

• No bars allowed outside of bodywork
  • includes nerf bars, tow bars, push bars and bumpers
    and external bars made of  unconventional materials such as polycarbonate and carbon fiber
  • Rule may be waived for 1 event at the discretion of officials
  • RUB RAILS: If used, must be carbonate type as manufactured by Five star bodies or similar.
                            No solid types; must be mounted directly to body. Only (1) per side.

• Must remain sealed at fenders
• No cutting or holes allowed

• 56 inches minimum
• Measured 10 inches back from leading edge of roof
   

• Minimum rear deck height 38 inches
• Max rear deck height 40 inches
• Must seal

• Flat-no lips or bends
• 10 inch
• Must extend entire width of rear deck
• May be braced from behind only
• Minimum 55 degrees
  • May be changed at discretion of series
  • Trucks that have spoilers that do not meet all of the above conditions at inspection
    will be assessed a 50 lb weight penalty. Spoiler must still pass before competing.

• No bars allowed outside of bodywork
  • includes nerf bars, tow bars, push bars and bumpers
    and external bars made of  unconventional materials such as polycarbonate and carbon fiber
  • Rule may be waived for 1 event at the discretion of officials
• RUB RAILS: If used, must be carbonate type as manufactured by Five star bodies or similar.
                          No solid types; must be mounted directly to body. Only (1) per side.

• Must remain sealed at fenders
• No cutting or holes allowed

• 52 inches  
• Measured 10 inches back from leading edge of  roof
• D Chassis must use AR or approved extended cab // full size roof
• D Chassis is recommended  to add 13-15 inch extension to roof to upgrade to full size. 
   

• Minimum Rear deck height 37 inches
• Max rear deck height 39 inches
• Must seal with the exception of openings for Automatic Transmission cooler ventilation.

• Flat-no lips or bends
• 10 inch
• Must extend entire width of rear deck
• May be braced from behind only
  • Spoiler must maintain setting with 15 lbs of pressure applied.
• Minimum 55 degrees
  • May be adjusted on a per track basis
    See individual entry blank
  • Trucks that have spoilers that do not meet all of the above conditions at inspection
    will be assessed a 50 lb weight penalty. Spoiler must pass before competing.

• No bars allowed outside of bodywork
  • includes nerf bars, tow bars, push bars and bumpers
    and external bars made of  unconventional materials such as polycarbonate and carbon fiber
  • Rule may be waived for 1 event at the discretion of officials
  • RUB RAILS: If used, must be carbonate type as manufactured by Five star bodies or similar.
                            No solid types; must be mounted directly to body. Only (1) per side.

• Must remain sealed at fenders
• No cutting or holes allowed
   

• 53 inches
• Measured 10 inches back from leading edge of roof
   

• Must cover front tire entirely
   

• Must cover rear tires entirely
• Max rear deck height 40 inches
• Must seal
   

• Flat-no lips or bends
• 10 inch
• Must extend entire width of rear deck
• May be braced from behind only
• Minimum 55 degrees
  • May be adjusted on a per track basis
    See individual entry blank
  • Trucks that have spoilers that do not meet all of the above conditions at inspection
    will be assessed a 50 lb weight penalty. Spoiler must still pass before competing.

S Metric Body Rules